How to Convert a Ceiling Light to a Recessed Light

Project Overview
  • Total Time: 1 - 2 hrs
  • Skill Level: Intermediate
  • Estimated Cost: $20-$100

Recessed lights provide directed lighting in kitchens, living rooms, and bedrooms. The best thing about recessed lights is that they are flush with the ceiling, so they tuck neatly away—which is the opposite of most ceiling lights.

Recessed lighting held up by hand with light on

The Spruce / Liz Moskowitz

Ceiling lights are surface-mounted. Embedded within the ceiling drywall is an electrical box with wires. But on the surface of the ceiling and quite prominent is the light. Some homeowners might not like this obstruction or they just might want a different type of light, and that's where recessed lights come in.

Converting a ceiling light to a recessed light takes some work, but it can be accomplished in less than a couple of hours by a do-it-yourselfer.

Before You Begin

Converting a standard ceiling light fixture to a recessed light involves removing the old fixture and its electrical box and installing the new recessed light—in the same place. Before doing so, it's worth considering a couple of aspects:

  • Recessed lights are not centrally located. Ceiling lights are usually centrally located within a room. Recessed lights usually are located along a room's perimeter. When you switch out a ceiling light for a recessed light, you end up with a recessed light in the middle of the room.
  • Removing the old electrical box can be difficult. The ceiling light's electrical box can be so difficult to remove that it's easier to leave the box in place.

Two options are to either transfer the existing wires to a new location or to run new wires to the new location. In either case, the ceiling light's electrical box is kept live and powered. But the light itself is removed and the face of the box is covered with a blank ceiling box cover.

Tip

If you don't have access to an attic above the ceiling, use a remodel light fixture that can be installed from below the ceiling.

Safety Considerations

Turn off the power to the ceiling light fixture first by turning off the light switch, then flipping off the appropriate circuit breaker in your home's breaker box. You cannot turn off the light switch only; this is dangerous. You must turn off the circuit breaker.

Be sure to use an IC-rated light, which is safe to be in contact with ceiling insulation. With fixtures that are not IC-rated, you must keep the insulation several inches away from the fixture housing to prevent a fire hazard. Leaving the housing and surrounding area without insulation creates a big thermal hole in your ceiling that lets heated air escape into the attic.

Need more help? Talk to a lighting installer near you

Our partners can help you compare quotes from top-rated professionals near you.


Get a Quote

The offers that appear in this table are from partnerships from which The Spruce receives compensation.

What You'll Need

Equipment / Tools

  • Screwdriver
  • Non-contact voltage tester
  • Pencil
  • Drywall saw
  • Hacksaw blade (as needed)

Materials

  • Recessed light fixture
  • Cable clamp
  • Wire connectors

Instructions

  1. Turn Power Off

    Turn the power off at the electric service panel by flipping off the circuit breaker. Turn the light on and off at the switch to confirm that it is not powered. If the light doesn't come on, you can proceed with the steps below.

    Inside Electric Service Panel
    Inside Electric Service Panel Fuse/Getty Images
  2. Open the Fixture and Test for Power

    Remove the dome or shade on the ceiling light, then remove all light bulbs. Use a screwdriver to remove any screws holding the housing to the electrical box. Carefully pull the fixture down a few inches to expose the wires. Test each wire with a non-contact voltage tester to confirm the power is off. If the tester detects any voltage, turn off the correct breaker and test the wires again.

    Fixture lowered and tested for power with a non-contact voltage tester

    The Spruce / Liz Moskowitz

  3. Remove the Fixture

    Unscrew the wire connectors joining the circuit wires to the light fixture wires, and separate the wires. Unless the wires are already very long or damaged in some way, don't just cut the wires. Doing so may leave them too short to use with the new fixture.

    Wires separated and screwed wire connectors from light fixture

    The Spruce / Liz Moskowitz

  4. Cut Out the Fixture Hole

    Place the cutting template from the new fixture over the opening for the electrical box. Using a pencil, trace around the template to mark a cutting outline. Cut along the outline with a drywall saw. Be careful not to damage any wiring inside the ceiling. Remove the cut pieces of drywall.

    Fixture hole cut out with drywall saw following outline

    The Spruce / Liz Moskowitz

    Tip

    If the new fixture does not come with a template, use a pencil compass to draw a circle on the ceiling that is slightly larger than the new fixture canister. The hole should be no more than 1/8 inch larger (in diameter) than the canister.

  5. Remove the Old Box

    Remove any screws securing the old electrical box to the ceiling framing. If the box is nailed in place, cut through the nails with a hacksaw blade. Loosen the cable clamp on the box to free the circuit cable, then remove the box from the ceiling.

    Old electrical box pulled out of ceiling

    The Spruce / Liz Moskowitz

  6. Connect the Circuit Cable

    Install a cable clamp onto the electrical splice box of the new light fixture, as needed. Feed the circuit cable through the clamp and into the splice box, then secure the cable by tightening the clamp's screws. At least 1/4-inch of the cable sheathing (outer jacket) should extend beyond the inside of the clamp.

    Electrical splice box connecting circuit cable with clamp

    The Spruce / Liz Moskowitz

  7. Connect the Fixture Wires

    Connect the circuit wires to the fixture wires, following the fixture manufacturer's wiring diagram. Secure each connection with a wire connector. Typically, the black (hot) circuit wire connects to the black (hot) fixture wire, the white (neutral) circuit wire connects to the white (neutral) fixture wire, and the bare copper (ground) circuit wire connects to the bare copper or green insulated fixture wire.

    Fixture wires connected with circuit wires

    The Spruce / Liz Moskowitz

  8. Install the Recessed Fixture

    Fit the fixture into the hole, inserting the portion with the splice box first, then the light canister. Reach inside of the canister and firmly snap the ceiling clips downward so they lock onto the backside of the drywall.

    If the fixture has a separate module that holds the light bulb, attach the module to the wires in the fixture housing, then push the module up into the canister. Install a light bulb.

    Recessed fixture installed into ceiling hole
    The Spruce / Liz Moskowitz

    Tip

    Make sure the light bulb does not exceed the maximum wattage rating of the fixture. With energy-efficient LED or CFL bulbs, it's almost impossible to exceed the rating. But it's not so hard with incandescent or halogen bulbs, which can have high wattages and run very hot.

  9. Turn On the Power

    Restore power to the light's circuit by turning on the circuit breaker, then test the light by turning on the light switch. If you have access to an attic space above the new fixture, cover the fixture with insulation (only if the fixture is IC-rated) to minimize the loss of room heat through the fixture.

    Recessed lighting held up by hand with light turned on

    The Spruce / Liz Moskowitz

The Spruce uses only high-quality sources, including peer-reviewed studies, to support the facts within our articles. Read our editorial process to learn more about how we fact-check and keep our content accurate, reliable, and trustworthy.
  1. Electrical Safety Foundation International. Electrical Safety Workbook.

  2. Installation Clearance Requirement for Recessed Luminaries. International Association of Electrical Inspectors.

  3. Energy Savings: LED Lighting. United States Department of Energy.